Tuesday, June 4, 2019

Internet Protocol Version 6 (IPv6) Analysis

Internet Protocol random variable 6 (IPv6) AnalysisOverviewInternet Protocol version 6 (IPv6) is the near generation of protocol defined by InternetEngineering Task force (IETF) to replace the exiting IPv4 protocol. At present, the volume of Internet users tingeic flake 18 still employ IPv4 protocol, and aband iodind that virtually of current mesh cyberspace topologying applications and entanglement equipment run in IPv4 environments, the migration from IPv4 to IPv6 provoket be accomplished all overnight. It is predictable that the migration ordain be a long-term adjoin (it is forecasted that the service go out take 10 20 years). During the migration, IPv4 and IPv6 get out coexist in a aforesaid(prenominal) interlocking. This migration process poses new ch bo thusges on the routers that ar the center field equipment in IP net feed. Traditional routers slant accommodate new future net profit with IPv4/v6 coexistence. The routers must be meliorate and upgra ded so that they stool livelihood both(prenominal) IPv4 and IPv6.Given that the affection router is actually im behaviorant and carries huge Internet crafts, it must be able to sanction IPv6 publicity at fit rate. It agency ASIC chip, but non softw be program is used to back up IPv6 mailboat processing. At the similar time, it is very im expressionant that this incarnate bank consecrate any IPv4 per engineerance. After only, most of current professions is IPv4. The institutionalize router must expand to clog IPv6 routing tables and shoots to support IPv6 routing protocols, such as BGP4+, OSPFv3, ISISv6, RIPng and etc. It necessarily to support virtually migration strategy from IPv4 to IPv6, such as Tunnel, triplex Stack, Translation and etc.Same as more profit technologies, successful deployment of IPv6 relies on the deployment of the operators IPv6 net profit. As ace core component in IPv6 net profit, IPv6 core router is draw to network building, ap plications, performance and stability. At present, mainstream router vendors like Cisco and juniper announce that their routers bottom of the inning support IPv6 piece of music approximately traditional IT equipment manufactures, especially those in Japan, cerebrate Internet upgrade caused by IPv6 will change the whole landscape of router trade, which brings signifi stackt opportunities for them to enter router market. From 2000 to 2002, Hitachi, necrotizing enterocolitis and Fujitsu announced IPv6-capable core router to gain some market sh ar in new Internet network.It must be admitted that IPv6 is still in the initial flesh at present, which is reflected in the following aspects most IPv6 network is in trial phase, the number of access users is low, carried IPv6 works cant be comparable to IPv4, the interoperability surrounded by IPv6 equipment still needs to be proved, and network engineers lack in follow out in large-scale deployment and operation of IPv6 network. The l ack of data and experience is one of important causes that make some operators lack in confidence in IPv6 network deployment. Many operators take wait-and-see attitudes. In coiffure to prove IPv6 router (especially IPv6 core router), the support to IPv6, how atomic number 18 they performed and interoperated, provide a practical data basis for the operators to deploy IPv6 network and provide a reference for equipment manufactures to evaluate and improve their equipment, BII(Beijing Internet Institute) collaborate with 6TNet (IPv6 Telecom Trial Network) in China raveled IPv6 core routers from 4 vendors (Fujitsu, Hitachi, Juniper and necrotizing enterocolitis) in Beijing fromOctober to December 2002. BII performed protocol conformance, performance andinteroperability studys. In these analyses, we used the exam musical instruments provided by Agilent and regaind strong technical support from Agilent.The trial run is not a comparative performance visitation in varied router ve ndors. The purpose is to swear the feasibility of IPv6 deployment. With this audition, the screen out police squad thinks that all SUT (system under probe) has the ability to support commercial IPv6 network and provide basic IPv6 capabilities. They can support IPv6 routing protocols, support the forwarding of IPv6 datagram at cable rate and provide interoperability between them. From perspectives of pure technology, the rill team thinks the products have been ready to deploy basic IPv6 core network..Brief Descriptions of tryoutThe requirements for hardw atomic number 18 provided by the SUT (system under tribulation) are as followsIPv6-capable core routerOC48 SM ports (both ports must be in different boards)Supports both FE ports and GE ports. The number of FE ports and GE ports is no less(prenominal) than 3Finally, all vendors basically meet those requirements, although CX5210 provided by NEC doesnt support FE during the time of testing.The requirement for IPv6 capabiliti es provided by the SUT (system under test) accept support of IPv6 forwarding in hardware and support of related IPv6 routing protocols and migration strategy. Finally, all vendors meet our requirements as shown in the following table.Company IPv6 hardwareDual Stack RIPng OSPFv3 BGP4+ IPv6 over IPv4forwarding TunnelFujitsu 9 9 9 9 9 9Hitachi 9 9 9 9 9 9Juniper 9 9 9 9 9 9NEC 9 9 9 9 9 9The SUT (system under test) stylels and OS versions are shown in the following table.Company Model pas seulFujitsu Geostream R920 E10V02L03C44Hitachi GR2000-20H S-9181-61 07-01 ROUTE-OS6Juniper M20 5.5R1.2NEC CX5210 02.0(2e) 45.08.00The test instruments we used in the test are as followsAgilent streetr streaker 900Version Router examer 5.1,Build 11.15. Agilent QA RobotVersion Router Tester 5.3,Build 5.2The IPv6 core router test is composed of three partsProtocol conformance test, interoperability test and IPv6 performance test. raw material IPv6 Protocols and RIPngBasic IPv6 protocols include IPv 6 Specification (RFC2460), ICMPv6 (RFC2463), Neighbor Discovery (RFC2461), dispossessed Autoconfiguration (RFC2462), Path MTU Discovery (RFC1981), IPv6 acknowledgment Architecture (RFC1884) and etc., which are basic capabilities provided by an IPv6 implementation.RIPng is defined by RFC2080 and is the mention and expansion of RIPv2. Its basic capabilities are equal as RIPv2. The routing culture exchanged by RIPng can carry IPv6 addresses and prefixes. RIPng runs on IPv6 network, uses multicasting address ff029 as savoir-faire to transfer routing information. RIPng is not compatible with RIPv2. RIP protocol is typically used in small networks and is not deployed in large networks because of its scalability and performance, which is same in IPv6 networks.The test does not include basic IPv6 protocols and RIPng because we think both capabilities are most basic and most preliminary capabilities that should be provided in an IPv6 router, these capabilities are implemented and inter operated very well in the routers from 4 vendors, and the 4 tried routers have been tested publicly or non-publicly several times in different occasions and provided broad(a) data. Therefore, we think it is un needful to make efforts to repeat these work and we skipped this test and focused on more than challenged test items.BGP4+ Protocol Conformance TestAt present, the outside(a) gateway protocol used in the IPv4 network is BGP4. Its basic protocolsare defined in RFC1771. In order to carry IPv6 network information in BGP4 updates, IETF has defined a special topographic point multi-protocol BGP (MP-BGP), withal called IPv6 NLRI (Network Layer Reachability Information) to exchange IPv6 routing information, which is not a new version of BGP protocol, but an extension to BGP4. The extension is largely called BGP4+, which is compatible with BGP4. Refer to RFC2545 for its definition.Test Purpose and apply StandardsPurpose To test the implementation of BGP4+ and conform with rel ated standards for SUT (System chthonic Test). The following standards are referred in the testBates, T., Chandra, R., Katz, D. and Y. Rekhter, Multiprotocol Extension for BGP-4, RFC 2858, Jne 2000.Bates, T., Chandra, R., Chen, E., BGP Route Reflection An Alternative to rich Mesh IBGP, RFC2796, April 2000.Chandra, R. and J.Scudder, Capabilities Advertisement with BGP-4, RFC 2842, May 2000.Dupont, F. and P. Marques, Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain Routing, RFC 2545, March 1999.Rekhter, Y. and T. Li, A Border Gateway Protocol 4 (BGP-4) .Traina, P., McPherson, D., Scudder, J., Autonomous System Con compacts for BGP, RFC3065, February 2001.Test Methods in all the tests are based on topology emulation. One test port of instrument first-class honours degreely leavees network topology emulation, then executes pre-written scripts, interacts with the port of SUT, performs related BGP4+ protocol tests separately and each test generates Passed/Failed record. The tests can be divided into active tests and passive tests. Active test means the examiner is used to vagabond the state form of SUT and the correctness of message format while passive test means the quizzer is used to substitute with SUT using messages with errors.Test TopologyTest instrument and SUT use two independent Fast Ethernet or Gigabit Ethernet connections. All BGP4+ runs on the Fast Ethernet or Gigabit Ethernet connections.The carnal topology is as followsThe logical topology is as followsTest Items and Descriptions of Test ResultsThe BGP4+ protocol conformance test involves in the BGP multi-protocol extension, setup and transfer of BGP4+ IBGP and EBGP sessions, ability to elate IPv6 route updates, BGP4+ next skip, starting point, MED, local preference, AS_PATH, atom aggregation, community name and various properties, the ability of SUT to correctly process these properties, BGP4+ route reflector efficacy, BGP4+ federation capability.These tests can exactly en sure implementation of BGP4+protocol in SUT comply with the standard defined by RFC, and cant ensure SUT fully and successfully deploy BGP4+ routes in commercial IPv6 network.The following diagram briefly describes the test results. Attached table 1 includes all test items, description and detailed results of BGP4+ conformance tests for 4 routers. The test items and descriptions are extracted from RFC2858, RFC2545, RFC2842, RFC2796, RFC3065 and draft-ietf-idr-bgp4-14.txt part.Model Failed test itemsFujitsu GeoStream R920 2Hitachi GR2000-20H 5Juniper M20 1NEC CX5210 3Analysis of Test ResultsCapabilities not supportedConfederationRoute reflector, CommunityFujitsus GeoStreamR920 of current version does not support BGP4+ federation capability. In all BGP4+ test items it supported, the general performance is fairly good. What needs to be alter is sole(prenominal) one item that is to support the migration of indefinable property and handle interim duration.It is hoped to improve null i nterface which cant support next hop at present.Hitachis GR2000-20H of current version supports all test items, and is only product fully supporting BGP4+ protocols in the core routers from 3 Japanese companies. However, it needs to be improved in the following areas handling next-hop property of IBGP in BGP4+ protocol, using AS_PATH properties to prevent from route loop, the ability of route reflector to detect ORIGINATOR_ID. At the same time, we free-base in the interoperability test that GR2000-20H cant register non-physical direct-connection sessions with IBGP peering entities, which Hitachi needs to improve. It is hoped to add loopback address capability.Junipers M20 passes all tests except one item excellently.NECs CX5210 of current version doesnt support BGP4+ route reflector and community properties. In all BGP4+ test items it supported, the general performance is fairly good. However, it needs to be improved in handling BGP4+ federation AS_CONFED_SEQUENCE property. It is hoped to add null interface configuration.Interoperability TestAs above mentioned, IPv6 is in initial phase of commercial deployment at present. A large amount of IPv6-capable network equipments and terminals are available. IPv6 network built by the operators doesnt only use the equipment provided by a vendor. In multi-vendor network environment, the interoperability between equipment is vital.The interoperability test is composed of BGP4+ interoperability test and OSPFv3 interoperability test. It should be noted that specific items in the interoperability test only cover some most common properties of BGP4+ and OSPFv3, and are not the interoperability tests of all properties of BGP4+ and OSPFv3.BGP4+ InteroperabilityEstablish IBGP SessionsTest Descriptions The test is to verify GR2000-20H, CX5210, R920,M20 and fully mesh iBGP connections that can be establish.Reference RFC1771, RFC2545 and RFC2858.Test steps GR2000-20H, CX5210, R920, M20 and SUT are connected as shown in the fol lowing diagram.4 routers are in a same autonomous humankind and are coordinated using IBGP protocol to form a full-meshed IBGP connection. Test instrument and SUT are interconnected using EBGPconnection. Because GR2000-20H doesnt support IBGP across-router Session connection, we use a FE link to connect GR2000-20H to M20 to form a fully-meshed connection.Test ResultsWe substantiate whether iBGP sessions were established between GR2000-20H, CX5210, R920 and M20, and it was demonstrate all connections were set up successfully.GR2000-20H CX5210 R920 M20GR2000-20H N/A OK OK OKCX5210 OK N/A OK OKR920 OK OK N/A OKM20 OK OK OK N/AEBGP- Route AdvertisementTest Descriptions To verify GR2000-20H, CX5210, R920 and M20 can advertise routes powerful in a fully meshed networks.References RFC1771, RFC2545 and RFC2858.Test steps Establish network topology according to previous test, establish eBGP connection between tester and SUT, institutionalize ampere-second EBGP routes from tester to SU T.ResultsWe verified whether GR2000-20H, CX5210 and R920 and M20 routing tables were correct, and it was found all routing tables were correct.GR2000-20H CX5210 R920 M20GR2000-20H N/A OK OK OKCX5210 OK N/A OK OKR920 OK OK N/A OKM20 OK OK OK N/AEstablish EBGP SessionsTest Descriptions The test is to verify GR2000-20H, CX5210, R920 and M20 can establish a fully meshed eBGP connections.Reference RFC1771, RFC2545 and RFC2858.Test steps GR2000-20H, CX5210, R920 and M20 are connected as shown in the following diagram.Test DescriptionsWe verified whether EBGP sessions were established between GR2000-20H, CX5210, R920 and M20, and it was found all connections were established successfully.GR2000-20H CX5210 R920 M20GR2000-20H N/A OK OK OKCX5210 OK N/A OK OKR920 OK OK N/A OKM20 OK OK OK N/AEBGP Route AdvertisementTest Descriptions To verify GR2000-20H, CX5210, R920 and M20 can advertise EBGP routes decently.References RFC1771, RFC2545 and RFC2858.Test steps Establish network topology accord ing to previous tests, send routes from each router to all other routers.Test ResultsWe verified whether GR2000-20H, CX5210 and R920 and M20 routing tables were correct, and it was found all routing tables were correct.GR2000-20H CX5210 R920, M20rGR2000-20H N/A OK OK OKCX5210 OK N/A OK OKR920 OK OK N/A OKM20 OK OK OK N/AOSPFv3 InteroperabilityOSPF protocols supporting IPv6 is OSPFv3. OSPFv3 routing mechanism is basically same asOSPFv2. However, OSPFv2 relies primarily on IPv4, while OSPFv3 makes more improvements in OSPFv2 and is not a simple extension, in that locationfore OSPFv3, whose corresponding protocol is RFC2740, runs on IPv6. For real world applications, many operators regard OSPFv3 as a betray new protocol, also its stability and maturity need to be further verified, so when IPv6 routing protocols are selected, it tends to use IS-ISv6 (draft-ietf-isis-ipv6-02.txt), which is only a simple extension to IS-ISv4 (RFC1195) (2 TLVs re-defined) and does not make changes full y. However, it is sure the opinion is not classical and need to be proved.Because of the limitations of test instrument, It is required for SUT to provide 100M Ethernet interface. As CX5210 does not support Ethernet interface at present, just M20, R920 and GR2000-20H were involved in the testing. However, it does not ask that CX5210 cant interoperate with other 3 routers and has any problems with functions implementation.In the test, GR2000-20H is called SUT1 in short, M20 is called SUT2, and R920 is called SUT3.Establish OSPF Connections DR ElectionTest DescriptionsIn the initial status, set different OSPF priority levels for SUT1, SUT2, SUT3 and the test instrument (10, 8, 5, 0). Connect these equipments based on the network topology below.Verify SUT1, SUT2, SUT3 and test instrument to establish OSPFv3 adjacency and vote DR/BDR.After DR/BDR is established properly, entrust DR off the network, and check whether DR/BDR is established properly.Put off-net equipment on the network , and check whether DR/BDR is established properly.Change OSPF initialization priorities of SUT1, SUT2, SUT3 and test instrument, and implement new test from step 2. tell the tests for 4 times, and ensure each SUT and test instrument have one opportunity to be selected as DR and BDR under the intial status.During the test, all SUTs are in the same OSPF Area 0.Reference RFC2740Test ResultsDuring the testing, all the OSPF adjacencys can be established between SUTs and DR, also BDR can be elected properly. After DR is off-line, BDR can be re-elected as DR and the one with sub-top priority will be BDR. When off-line equipment is on-line again, no re-electing process occurs. All test results comply with the requirements in related standards. permute LSA DatabaseTest Descriptions Test instrument simulates an internal network with 4 routers connected, and sends the routing information to SUT. Then verify the routing information received by SUT DR from test instruments will be sent to DR Other correctly. Same as the previous test item, firstly SUT1 is used as DR, then SUT2, and terminally SUT3.Reference RFC2740Test ResultsDuring the testing, OSPF adjacency can be established properly between all SUTs. DR receiveLSA information from test instrument and properly send the information to DR Other, which can also receive and process LSA information properly.IPv6 action TestThe major approach used for the performance testing was to send the IPv6 merchandise with different bundle coats and specific QoS information, via SUT to the destination, and then by the tester measure the throughput, latency and software package loss of SUT in various topologies. For the IPv6 performance test, there are four vendors high-end IPv6 routers, with OC-48 POS ports on which throughput and latency will be measured, with IPv6 tract surfaces of 64 bytes, 128bytes, 256 bytes, 512 bytes, 1024 bytes, 1480 bytes and 1500 bytes. The performance in various of circumstances were measured, in cluding IPv4/IPv6 mixed traffics (IPv4 and IPv6 traffics with different ratio), IPv6 traffic with packet surfaces mixtures, Sweep share Sizes. Also the level best routing table entry supported and the performance on manually configured tunnels were verified. Most of the referred standards is extracted from RFC2544.At present, there are deficient applications for IPv6, and the number of users in the IPv6 network can not be compared to IPv4. The sum of maximum IPv6 of IX(Internet eXchage) traffics is lessthan dozens of Mbits/s. These traffics can be handled using a router refitted from a PC. Based on the circumstance, is it necessary to test the performance of OC48 ports ? Actually when the operators build IPv6 network and purchase IPv6 routers, todays IPv6 network is not under their consideration. Their networks should be able to deal with the changes and maturement of IPv6 network next 5 7 years. In this sense, it is necessary for IPv6 core router to support the IPv6 traffic fo rwarding capacities at wire rate. Otherwise, what differences can be made between a real IPv6 router and a router refitted from a PC with installed BSD and Zebra ?The measurement of the number of routing table entry also meets the same situations. At present, therere around 300-400 entries in the IPv6 backbone router routing table, which cant comparedto the huge number of IPv4 (110,000130,000 routes). Secondly, IPv6 has drawn experience and lessons from IPv4 in design and address assignment. RIR only assigns the large stave off and fixed length IPv6 addresses to IPv6 operators, instead of the end users. To some extent, this can protect IPv6 routing tables from the explosive growth. The strict prefix filtering mechanism was set on BGP4+ routers by most of IPv6 network administrators and the router only allows minor prefixes, such as /16, /24, /28, /32, /35 and etc. However, the experience of IPv4 teach us a lesson- Money Talks. In the fiercely competitive ages, it is very difficult for operators to reject users requirements. Under the conditions that IPv6 doesnt solve the problems of Multi-homing completely, it is possible that the network operators are required to broadcast users network prefixes into global IPv6 routing tables in order to achieve Multi-homing applications. So far RIR has begun to assign /48 address segment to IPv6 of IX independently, while it is suggested IX doesnt broadcast the addresses. Thirdly, in many IPv6 networks, there are at least two IPv6 addresses segments, from 6BONE(3ffe/16) and RIR(2001/16) respectively, and maybe more prefixes will appear in the future. Fourthly, RIR cant ensure IPV6 addresses appoint to IPv6 operators are from a continuous address block. Current assignment policy indicates that /32 addresses of IPv6 charge to operators can be continuously extended to /29. If new addresses are further required, they must be assigned to discontinuous address blocks and result in the growth of the number of routing tables. T o sum up, the test team suggests that the number of IPv6 routing tables supported by the router should be no less than that of IPv4 routing tables, since it is very difficult to estimate the increasing number of routing tables of IPv6 core network right now.In current IPv6 networks, commercial IPv6 network and IPv6 trial network (6BONE) are interlaced without a explicit boundary between them. A packet from commercial IPv6 network may go through many IPv6 trial network before arriving at another IPv6 network. The network administrators of many trial networks are not regarded as a operators, but a players It is pretty unstable of their networks, with routers reset very frequently. In the meantime, the networks advertise global IPv6 routes to all peers, making their own IPv6 network to implement transit. It causes the instability of current IPv6 of BGP routes, and thus it is required the capabilities of IPv6 routers cover the fluttering and convergence properly, which should be inclu ded in this test, nonetheless due to limited test time frame, it is a pity the test team has to give up these tests.The network topology used for the performance test is shown as followingIdeally, the test topology should be as following, so that the packet forwarding capability of the routers in real-world network environment is shown completely.Send one traffic from a source port of the tester, via multiple ports of the router to the destination ports of tester, measure the performance of the router. However as the vendors cant provide enough OC48 ports, the test team can only perform the test by simply sending packets from one port and receiving packets form another port. In this sense, this test environment cant simulate completely the performance of the router in the real-world network environment.The Measurement of Throughput and latency with opposite IPv6 Packets Sizes at OC-48 POS portTest Descriptions To test the maximum IPv6 packet forwarding rate of SUT with zero packet loss with different IPv6 packet sizes.Test Methods Send IPv6 packets, via SUT to the destination ports of the tester, which measures the packet rate of SUT according to the received IPv6 packets. Set the initial offered load to 2%, and If no packet loss occurs, add-on the offered load to 100% and repeat the test. If packet loss occurs, decrease the offered load to (100%+2%)/2=51%, repeat the test againIn a binary search manner, continue to increase or decrease the offered load in succeeding iterations until the difference in offered load between successful and failed tests is less than the resolution for the test. This is the zero-loss throughput rate. concern forwarding mode full duplex. Offered Packet type IPv6Offered Packet size (bytes) 64 128 256 512 1024 1480 1500 Test duration of each packet type(s) 5Bandwidth resolution (%) 0.1 Line BER tolerance (10_) -10The results are as followssustainable Throughput of OC-48 POS miencv.00%100.00%95.00%90.00%85.00%80.00%75.00%70.00%65. 00%60.00%55.00%50.00%64 128 256 512 1024 1480 1500bytes bytes bytes bytes bytes bytes bytesTest Packets Size clean Latency (us) at Variable Test Packets Size1009080706050403020100Test Packets SizeHitachiNECFujistu JuniperHitachi NECFujistu Juniper bank note About underlying latency of tester ahead we perform tests, we must consider intrinsic latency of tester. The following table indicates inherent latency of tester for different test packet sizes when sending 100% offered load.Inherent latency of tester (100% offered load)Packet Size (bytes) 64 128 256 512 1024 1480 1500Average Inherent 2.74 2.69 2.69 2.65 2.65 2.60 2.60Latency (us)From the above, the inherent latency of tester under different packet sizes is about 2.7us. Compared to the tens of us of SUTs latency, there are not significant conflicts on the test results. In addition, the impact of inherent latency is fair to these 4 SUTs. forwarding Performance of IPv4/IPv6 Packets on OC48 PortsTest Descriptions To verify the per formance of SUT to forward IPv4/IPv6 packets in offered packets sizes. The test requires SUT to support IPv4/IPv6 bivalent protocol stacks.Test Methods The tester sends IPv4 and IPv6 traffic simultaneously in full duplex configuration, via SUT to the destination port, measure the throughput and latency with various ratio of IPv4 and IPv6 traffic. Send traffic with 50% of IPv4 and 50% of IPv6 and 100% offered load first time. If packet loss occurs, decrease the offered load in 5% resolution until the difference in offered load between successful and failed tests is less than the resolution for the test. This is the zero-loss throughput rate. At the same time, measure the latency at maximum forwarding rate. Then change the ratio of IPv4 and IPv6 traffic to test again. Increase continuously the proportion of IPv6 traffic to simulate the change of traffic characteristics in the real-world network transition.Test DescriptionsOffered load (%) initial100% with 5% increment and final 0 Off ered packet types IPv6 share of IPv4 and IPv6 traffic 50501090 (IPv4IPv6) Offered packet size (bytes) 62 512 1518Test duration of each packet size(s) 5 The test results are as followsSustainable throughput of OC-48 POS port at packet size 64 bytes with different component ofIPv4 and IPv6 trafficSustainable Throughput of OC-48 POS Port at Packet Size 64 bytes with different contribution of IPv4 and IPv6 Traffic105%100% 95% 90%85% Hitachi80% NEC75% Fujistu70% Juniper65% 60% 55% 50%50/50 40/60 30/70 20/80 10/90IPv4/IPv6 Test Packets section (IPv4/IPv6)Sustainable throughput of OC-48 POS port at packet size 512 bytes with different percentage of IPv4 and IPv6 trafficSustainable Throughput of OC-48 POS Port at Packet Size 512bytes with different Percentage of IPv4 and IPv6 Traffic105%100% 95% 90%85% Hitachi80% NEC75% Fujistu70% Juniper65% 60% 55% 50%50/50 40/60 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)Sustainable throughput of OC-48 POS port at packet size 1518 by tes with different percentage of IPv4 and IPv6 trafficSustainable Throughput of OC-48 POS Port at Packet Size 1518 bytes with different Percentage of IPv4 and IPv6 Traffic105%100% 95% 90%85% Hitachi80% NEC75% Fujistu70% Juniper65% 60% 55% 50%50/50 40/60 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)Average latency (us) at test packets size 64 bytes with different percentage of IPv4 and IPv6 trafficAverage Latency (us) at Test Packets Size 64 bytes withDifferent Percentage of IPv4 and IPv6 Traffic100908070605040302010050/50 40/6 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)HitachiNECFujistu JuniperAverage latency (us) at test packets size 512 bytes with different percentage of IPv4 and IPv6 trafficAverage Latency (us) at Test Packets Size 512 bytes with Different Percentage of IPv4 and IPv6 Traffic100908070605040302010050/50 40/60 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)HitachiNECFujistu JuniperAverage latency (us) at test packet s size 1518 bytes with different percentage of IPv4 and IPv6 trafficAverage Latency (us) at Test Packets Size 1518 bytes withDifferent Percentage of IPv4 and IPv6 Traffic100908070605040302010050/50 40/60 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)HitachiNECFujistu JuniperIPv6 over IPv4 Configured Tunneling Performance of OC-48 POS PortTest Description Tunneling technology is an effective means to connect separate IPv6 networks via IPv4 backbone. This item is to verify the performance of SUT when SUT encapsulates IPv6 data packets into IPv4 payload and forwards the packets.Test Method The tester sends IPv6 data packets to SUT, and configures an IPv6 over IPv4 tunnel between SUT and the tester. Thus after SUT receives pure IPv6 packets from the tester, it will encapsulate it into IPv4 packet payload, and send IPv6 packets to destination over IPv4 network. The tester analyzes the packets forwared by the SUT at receiving end, calculates the throughput of SUT for diffe rent sizes of packets under the IPv6 over IPv4 configured tunnel. Test ResultsIPv6 packet size 512Destination address of sending IPv6 data packets 3FFE0042/64Bandwidth range of sending IPv6 traInternet Protocol Version 6 (IPv6) AnalysisInternet Protocol Version 6 (IPv6) AnalysisOverviewInternet Protocol version 6 (IPv6) is the next generation of protocol defined by InternetEngineering Task force (IETF) to replace the exiting IPv4 protocol. At present, the majority of Internet users are still using IPv4 protocol, and given that most of current networking applications and network equipment run in IPv4 environments, the migration from IPv4 to IPv6 cant be accomplished overnight. It is predictable that the migration will be a long-term process (it is forecasted that the process will take 10 20 years). During the migration, IPv4 and IPv6 will coexist in a same network. This migration process poses new challenges on the routers that are the core equipment in IP network. Traditional route rs cant accommodate new future network with IPv4/v6 coexistence. The routers must be improved and upgraded so that they can support both IPv4 and IPv6.Given that the core router is very important and carries huge Internet traffics, it must be able to support IPv6 forwarding at wire rate. It means ASIC chip, but not software is used to support IPv6 packet processing. At the same time, it is very important that this support cant sacrifice any IPv4 performance. After all, most of current traffics is IPv4. The core router must expand to support IPv6 routing tables and needs to support IPv6 routing protocols, such as BGP4+, OSPFv3, ISISv6, RIPng and etc. It needs to support some migration strategy from IPv4 to IPv6, such as Tunnel, Dual Stack, Translation and etc.Same as many network technologies, successful deployment of IPv6 relies on the deployment of the operators IPv6 network. As one core component in IPv6 network, IPv6 core router is key to network building, applications, performan ce and stability. At present, mainstream router vendors like Cisco and Juniper announce that their routers can support IPv6 while some traditional IT equipment manufactures, especially those in Japan, think Internet upgrade caused by IPv6 will change the whole landscape of router market, which brings significant opportunities for them to enter router market. From 2000 to 2002, Hitachi, NEC and Fujitsu announced IPv6-capable core router to gain some market share in new Internet network.It must be admitted that IPv6 is still in the initial phase at present, which is reflected in the following aspects most IPv6 network is in trial phase, the number of access users is low, carried IPv6 traffics cant be comparable to IPv4, the interoperability between IPv6 equipment still needs to be proved, and network engineers lack in experience in large-scale deployment and operation of IPv6 network. The lack of data and experience is one of important causes that make some operators lack in confidenc e in IPv6 network deployment. Many operators take wait-and-see attitudes. In order to prove IPv6 router (especially IPv6 core router), the support to IPv6, how are they performed and interoperated, provide a practical data basis for the operators to deploy IPv6 network and provide a reference for equipment manufactures to evaluate and improve their equipment, BII(Beijing Internet Institute) collaborate with 6TNet (IPv6 Telecom Trial Network) in China tested IPv6 core routers from 4 vendors (Fujitsu, Hitachi, Juniper and NEC) in Beijing fromOctober to December 2002. BII performed protocol conformance, performance andinteroperability tests. In these tests, we used the test instruments provided by Agilent and received strong technical support from Agilent.The test is not a comparative performance test in different router vendors. The purpose is to verify the feasibility of IPv6 deployment. With this test, the test team thinks that all SUT (system under test) has the ability to support commercial IPv6 network and provide basic IPv6 capabilities. They can support IPv6 routing protocols, support the forwarding of IPv6 datagram at wire rate and provide interoperability between them. From perspectives of pure technology, the test team thinks the products have been ready to deploy basic IPv6 core network..Brief Descriptions of TestThe requirements for hardware provided by the SUT (system under test) are as followsIPv6-capable core routerOC48 SM ports (both ports must be in different boards)Supports both FE ports and GE ports. The number of FE ports and GE ports is no less than 3Finally, all vendors basically meet those requirements, although CX5210 provided by NEC doesnt support FE during the time of testing.The requirement for IPv6 capabilities provided by the SUT (system under test) include support of IPv6 forwarding in hardware and support of related IPv6 routing protocols and migration strategy. Finally, all vendors meet our requirements as shown in the following t able.Company IPv6 hardwareDual Stack RIPng OSPFv3 BGP4+ IPv6 over IPv4forwarding TunnelFujitsu 9 9 9 9 9 9Hitachi 9 9 9 9 9 9Juniper 9 9 9 9 9 9NEC 9 9 9 9 9 9The SUT (system under test) models and OS versions are shown in the following table.Company Model VersionFujitsu Geostream R920 E10V02L03C44Hitachi GR2000-20H S-9181-61 07-01 ROUTE-OS6Juniper M20 5.5R1.2NEC CX5210 02.0(2e) 45.08.00The test instruments we used in the test are as followsAgilent Router Tester 900Version Router Tester 5.1,Build 11.15. Agilent QA RobotVersion Router Tester 5.3,Build 5.2The IPv6 core router test is composed of three partsProtocol conformance test, interoperability test and IPv6 performance test.Basic IPv6 Protocols and RIPngBasic IPv6 protocols include IPv6 Specification (RFC2460), ICMPv6 (RFC2463), Neighbor Discovery (RFC2461), Stateless Autoconfiguration (RFC2462), Path MTU Discovery (RFC1981), IPv6 address Architecture (RFC1884) and etc., which are basic capabilities provided by an IPv6 implement ation.RIPng is defined by RFC2080 and is the extension and expansion of RIPv2. Its basic capabilities are same as RIPv2. The routing information exchanged by RIPng can carry IPv6 addresses and prefixes. RIPng runs on IPv6 network, uses multicasting address ff029 as destination to transfer routing information. RIPng is not compatible with RIPv2. RIP protocol is typically used in small networks and is not deployed in large networks because of its scalability and performance, which is same in IPv6 networks.The test does not include basic IPv6 protocols and RIPng because we think both capabilities are most basic and most preliminary capabilities that should be provided in an IPv6 router, these capabilities are implemented and interoperated very well in the routers from 4 vendors, and the 4 tested routers have been tested publicly or non-publicly several times in different occasions and provided good data. Therefore, we think it is unnecessary to make efforts to repeat these work and we skipped this test and focused on more challenged test items.BGP4+ Protocol Conformance TestAt present, the external gateway protocol used in the IPv4 network is BGP4. Its basic protocolsare defined in RFC1771. In order to carry IPv6 network information in BGP4 updates, IETF has defined a special property multi-protocol BGP (MP-BGP), also called IPv6 NLRI (Network Layer Reachability Information) to exchange IPv6 routing information, which is not a new version of BGP protocol, but an extension to BGP4. The extension is generally called BGP4+, which is compatible with BGP4. Refer to RFC2545 for its definition.Test Purpose and Used StandardsPurpose To test the implementation of BGP4+ and conform with related standards for SUT (System Under Test). The following standards are referred in the testBates, T., Chandra, R., Katz, D. and Y. Rekhter, Multiprotocol Extension for BGP-4, RFC 2858, Jne 2000.Bates, T., Chandra, R., Chen, E., BGP Route Reflection An Alternative to Full Mesh IBGP, RF C2796, April 2000.Chandra, R. and J.Scudder, Capabilities Advertisement with BGP-4, RFC 2842, May 2000.Dupont, F. and P. Marques, Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain Routing, RFC 2545, March 1999.Rekhter, Y. and T. Li, A Border Gateway Protocol 4 (BGP-4) .Traina, P., McPherson, D., Scudder, J., Autonomous System Confederations for BGP, RFC3065, February 2001.Test MethodsAll the tests are based on topology emulation. One test port of instrument firstly establishes network topology emulation, then executes pre-written scripts, interacts with the port of SUT, performs related BGP4+ protocol tests individually and each test generates Passed/Failed record. The tests can be divided into active tests and passive tests. Active test means the tester is used to verify the state machine of SUT and the correctness of message format while passive test means the tester is used to interfere with SUT using messages with errors.Test TopologyTest instrument and SUT use two ind ependent Fast Ethernet or Gigabit Ethernet connections. All BGP4+ runs on the Fast Ethernet or Gigabit Ethernet connections.The physical topology is as followsThe logical topology is as followsTest Items and Descriptions of Test ResultsThe BGP4+ protocol conformance test involves in the BGP multi-protocol extension, setup and transfer of BGP4+ IBGP and EBGP sessions, ability to receive IPv6 route updates, BGP4+ next hop, starting point, MED, local preference, AS_PATH, atom aggregation, community name and various properties, the ability of SUT to correctly process these properties, BGP4+ route reflector capability, BGP4+ federation capability.These tests can only ensure implementation of BGP4+protocol in SUT comply with the standard defined by RFC, and cant ensure SUT fully and successfully deploy BGP4+ routes in commercial IPv6 network.The following diagram briefly describes the test results. Attached table 1 includes all test items, description and detailed results of BGP4+ conform ance tests for 4 routers. The test items and descriptions are extracted from RFC2858, RFC2545, RFC2842, RFC2796, RFC3065 and draft-ietf-idr-bgp4-14.txt part.Model Failed test itemsFujitsu GeoStream R920 2Hitachi GR2000-20H 5Juniper M20 1NEC CX5210 3Analysis of Test ResultsCapabilities not supportedConfederationRoute reflector, CommunityFujitsus GeoStreamR920 of current version does not support BGP4+ federation capability. In all BGP4+ test items it supported, the general performance is fairly good. What needs to be improved is only one item that is to support the migration of undefined property and handle interim duration.It is hoped to improve null interface which cant support next hop at present.Hitachis GR2000-20H of current version supports all test items, and is only product fully supporting BGP4+ protocols in the core routers from 3 Japanese companies. However, it needs to be improved in the following areas handling next-hop property of IBGP in BGP4+ protocol, using AS_PATH pr operties to prevent from route loop, the ability of route reflector to detect ORIGINATOR_ID. At the same time, we found in the interoperability test that GR2000-20H cant establish non-physical direct-connection sessions with IBGP peering entities, which Hitachi needs to improve. It is hoped to add loopback address capability.Junipers M20 passes all tests except one item excellently.NECs CX5210 of current version doesnt support BGP4+ route reflector and community properties. In all BGP4+ test items it supported, the general performance is fairly good. However, it needs to be improved in handling BGP4+ federation AS_CONFED_SEQUENCE property. It is hoped to add null interface configuration.Interoperability TestAs above mentioned, IPv6 is in initial phase of commercial deployment at present. A large amount of IPv6-capable network equipments and terminals are available. IPv6 network built by the operators doesnt only use the equipment provided by a vendor. In multi-vendor network environ ment, the interoperability between equipment is vital.The interoperability test is composed of BGP4+ interoperability test and OSPFv3 interoperability test. It should be noted that specific items in the interoperability test only cover some most common properties of BGP4+ and OSPFv3, and are not the interoperability tests of all properties of BGP4+ and OSPFv3.BGP4+ InteroperabilityEstablish IBGP SessionsTest Descriptions The test is to verify GR2000-20H, CX5210, R920,M20 and fully meshed iBGP connections that can be established.Reference RFC1771, RFC2545 and RFC2858.Test steps GR2000-20H, CX5210, R920, M20 and SUT are connected as shown in the following diagram.4 routers are in a same autonomous domain and are interconnected using IBGP protocol to form a full-meshed IBGP connection. Test instrument and SUT are interconnected using EBGPconnection. Because GR2000-20H doesnt support IBGP across-router Session connection, we use a FE link to connect GR2000-20H to M20 to form a fully-mes hed connection.Test ResultsWe verified whether iBGP sessions were established between GR2000-20H, CX5210, R920 and M20, and it was found all connections were set up successfully.GR2000-20H CX5210 R920 M20GR2000-20H N/A OK OK OKCX5210 OK N/A OK OKR920 OK OK N/A OKM20 OK OK OK N/AEBGP- Route AdvertisementTest Descriptions To verify GR2000-20H, CX5210, R920 and M20 can advertise routes properly in a fully meshed networks.References RFC1771, RFC2545 and RFC2858.Test steps Establish network topology according to previous test, establish eBGP connection between tester and SUT, send 100 EBGP routes from tester to SUT.ResultsWe verified whether GR2000-20H, CX5210 and R920 and M20 routing tables were correct, and it was found all routing tables were correct.GR2000-20H CX5210 R920 M20GR2000-20H N/A OK OK OKCX5210 OK N/A OK OKR920 OK OK N/A OKM20 OK OK OK N/AEstablish EBGP SessionsTest Descriptions The test is to verify GR2000-20H, CX5210, R920 and M20 can establish a fully meshed eBGP connect ions.Reference RFC1771, RFC2545 and RFC2858.Test steps GR2000-20H, CX5210, R920 and M20 are connected as shown in the following diagram.Test DescriptionsWe verified whether EBGP sessions were established between GR2000-20H, CX5210, R920 and M20, and it was found all connections were established successfully.GR2000-20H CX5210 R920 M20GR2000-20H N/A OK OK OKCX5210 OK N/A OK OKR920 OK OK N/A OKM20 OK OK OK N/AEBGP Route AdvertisementTest Descriptions To verify GR2000-20H, CX5210, R920 and M20 can advertise EBGP routes properly.References RFC1771, RFC2545 and RFC2858.Test steps Establish network topology according to previous tests, send routes from each router to all other routers.Test ResultsWe verified whether GR2000-20H, CX5210 and R920 and M20 routing tables were correct, and it was found all routing tables were correct.GR2000-20H CX5210 R920, M20rGR2000-20H N/A OK OK OKCX5210 OK N/A OK OKR920 OK OK N/A OKM20 OK OK OK N/AOSPFv3 InteroperabilityOSPF protocols supporting IPv6 is OSP Fv3. OSPFv3 routing mechanism is basically same asOSPFv2. However, OSPFv2 relies primarily on IPv4, while OSPFv3 makes many improvements in OSPFv2 and is not a simple extension, thus OSPFv3, whose corresponding protocol is RFC2740, runs on IPv6. For real world applications, many operators regard OSPFv3 as a brand new protocol, also its stability and maturity need to be further verified, so when IPv6 routing protocols are selected, it tends to use IS-ISv6 (draft-ietf-isis-ipv6-02.txt), which is only a simple extension to IS-ISv4 (RFC1195) (2 TLVs re-defined) and does not make changes fully. However, it is sure the opinion is not authoritative and need to be proved.Because of the limitations of test instrument, It is required for SUT to provide 100M Ethernet interface. As CX5210 does not support Ethernet interface at present, just M20, R920 and GR2000-20H were involved in the testing. However, it does not imply that CX5210 cant interoperate with other 3 routers and has any problems wi th functions implementation.In the test, GR2000-20H is called SUT1 in short, M20 is called SUT2, and R920 is called SUT3.Establish OSPF Connections DR ElectionTest DescriptionsIn the initial status, set different OSPF priority levels for SUT1, SUT2, SUT3 and the test instrument (10, 8, 5, 0). Connect these equipments based on the network topology below.Verify SUT1, SUT2, SUT3 and test instrument to establish OSPFv3 adjacency and vote DR/BDR.After DR/BDR is established properly, put DR off the network, and check whether DR/BDR is established properly.Put off-net equipment on the network, and check whether DR/BDR is established properly.Change OSPF initialization priorities of SUT1, SUT2, SUT3 and test instrument, and implement new test from step 2. Repeat the tests for 4 times, and ensure each SUT and test instrument have one opportunity to be selected as DR and BDR under the intial status.During the test, all SUTs are in the same OSPF Area 0.Reference RFC2740Test ResultsDuring the testing, all the OSPF adjacencys can be established between SUTs and DR, also BDR can be elected properly. After DR is off-line, BDR can be re-elected as DR and the one with sub-top priority will be BDR. When off-line equipment is on-line again, no re-electing process occurs. All test results comply with the requirements in related standards.Exchange LSA DatabaseTest Descriptions Test instrument simulates an internal network with 4 routers connected, and sends the routing information to SUT. Then verify the routing information received by SUT DR from test instruments will be sent to DR Other correctly. Same as the previous test item, firstly SUT1 is used as DR, then SUT2, and finally SUT3.Reference RFC2740Test ResultsDuring the testing, OSPF adjacency can be established properly between all SUTs. DR receiveLSA information from test instrument and properly send the information to DR Other, which can also receive and process LSA information properly.IPv6 Performance TestThe major appr oach used for the performance testing was to send the IPv6 traffic with different packet sizes and specific QoS information, via SUT to the destination, and then by the tester measure the throughput, latency and packet loss of SUT in various topologies. For the IPv6 performance test, there are four vendors high-end IPv6 routers, with OC-48 POS ports on which throughput and latency will be measured, with IPv6 packet sizes of 64 bytes, 128bytes, 256 bytes, 512 bytes, 1024 bytes, 1480 bytes and 1500 bytes. The performance in various of circumstances were measured, including IPv4/IPv6 mixed traffics (IPv4 and IPv6 traffics with different ratio), IPv6 traffic with packet sizes mixtures, Sweep Packet Sizes. Also the maximum routing table entry supported and the performance on manually configured tunnels were verified. Most of the referred standards is extracted from RFC2544.At present, there are deficient applications for IPv6, and the number of users in the IPv6 network can not be compar ed to IPv4. The sum of maximum IPv6 of IX(Internet eXchage) traffics is lessthan dozens of Mbits/s. These traffics can be handled using a router refitted from a PC. Based on the circumstance, is it necessary to test the performance of OC48 ports ? Actually when the operators build IPv6 network and purchase IPv6 routers, todays IPv6 network is not under their consideration. Their networks should be able to deal with the changes and growth of IPv6 network next 5 7 years. In this sense, it is necessary for IPv6 core router to support the IPv6 traffic forwarding capacities at wire rate. Otherwise, what differences can be made between a real IPv6 router and a router refitted from a PC with installed BSD and Zebra ?The measurement of the number of routing table entry also meets the same situations. At present, therere around 300-400 entries in the IPv6 backbone router routing table, which cant comparedto the huge number of IPv4 (110,000130,000 routes). Secondly, IPv6 has drawn experience and lessons from IPv4 in design and address assignment. RIR only assigns the large block and fixed length IPv6 addresses to IPv6 operators, instead of the end users. To some extent, this can protect IPv6 routing tables from the explosive growth. The strict prefix filtering mechanism was set on BGP4+ routers by most of IPv6 network administrators and the router only allows minor prefixes, such as /16, /24, /28, /32, /35 and etc. However, the experience of IPv4 teach us a lesson- Money Talks. In the fiercely competitive ages, it is very difficult for operators to reject users requirements. Under the conditions that IPv6 doesnt solve the problems of Multi-homing completely, it is possible that the network operators are required to broadcast users network prefixes into global IPv6 routing tables in order to achieve Multi-homing applications. So far RIR has begun to assign /48 address segment to IPv6 of IX independently, while it is suggested IX doesnt broadcast the addresses. Thirdly, in many IPv6 networks, there are at least two IPv6 addresses segments, from 6BONE(3ffe/16) and RIR(2001/16) respectively, and maybe more prefixes will appear in the future. Fourthly, RIR cant ensure IPV6 addresses assigned to IPv6 operators are from a continuous address block. Current assignment policy indicates that /32 addresses of IPv6 assigned to operators can be continuously extended to /29. If new addresses are further required, they must be assigned to discontinuous address blocks and result in the growth of the number of routing tables. To sum up, the test team suggests that the number of IPv6 routing tables supported by the router should be no less than that of IPv4 routing tables, since it is very difficult to estimate the increasing number of routing tables of IPv6 core network right now.In current IPv6 networks, commercial IPv6 network and IPv6 trial network (6BONE) are interlaced without a explicit boundary between them. A packet from commercial IPv6 network may go thro ugh many IPv6 trial network before arriving at another IPv6 network. The network administrators of many trial networks are not regarded as a operators, but a players It is pretty unstable of their networks, with routers reset very frequently. In the meantime, the networks advertise global IPv6 routes to all peers, making their own IPv6 network to implement transit. It causes the instability of current IPv6 of BGP routes, and thus it is required the capabilities of IPv6 routers cover the flapping and convergence properly, which should be included in this test, however due to limited test time frame, it is a pity the test team has to give up these tests.The network topology used for the performance test is shown as followingIdeally, the test topology should be as following, so that the packet forwarding capability of the routers in real-world network environment is shown completely.Send one traffic from a source port of the tester, via multiple ports of the router to the destination p orts of tester, measure the performance of the router. However as the vendors cant provide enough OC48 ports, the test team can only perform the test by simply sending packets from one port and receiving packets form another port. In this sense, this test environment cant simulate completely the performance of the router in the real-world network environment.The Measurement of Throughput and Latency with Different IPv6 Packets Sizes at OC-48 POS portTest Descriptions To test the maximum IPv6 packet forwarding rate of SUT with zero packet loss with different IPv6 packet sizes.Test Methods Send IPv6 packets, via SUT to the destination ports of the tester, which measures the packet rate of SUT according to the received IPv6 packets. Set the initial offered load to 2%, and If no packet loss occurs, increase the offered load to 100% and repeat the test. If packet loss occurs, decrease the offered load to (100%+2%)/2=51%, repeat the test againIn a binary search manner, continue to increas e or decrease the offered load in subsequent iterations until the difference in offered load between successful and failed tests is less than the resolution for the test. This is the zero-loss throughput rate.Traffic forwarding mode full duplex. Offered Packet type IPv6Offered Packet size (bytes) 64 128 256 512 1024 1480 1500 Test duration of each packet type(s) 5Bandwidth resolution (%) 0.1 Line BER tolerance (10_) -10The results are as followsSustainable Throughput of OC-48 POS Port105.00%100.00%95.00%90.00%85.00%80.00%75.00%70.00%65.00%60.00%55.00%50.00%64 128 256 512 1024 1480 1500bytes bytes bytes bytes bytes bytes bytesTest Packets SizeAverage Latency (us) at Variable Test Packets Size1009080706050403020100Test Packets SizeHitachiNECFujistu JuniperHitachi NECFujistu JuniperNote About inherent latency of testerBefore we perform tests, we must consider intrinsic latency of tester. The following table indicates inherent latency of tester for different test packet sizes when sendi ng 100% offered load.Inherent latency of tester (100% offered load)Packet Size (bytes) 64 128 256 512 1024 1480 1500Average Inherent 2.74 2.69 2.69 2.65 2.65 2.60 2.60Latency (us)From the above, the inherent latency of tester under different packet sizes is about 2.7us. Compared to the tens of us of SUTs latency, there are not significant impacts on the test results. In addition, the impact of inherent latency is fair to these 4 SUTs.Forwarding Performance of IPv4/IPv6 Packets on OC48 PortsTest Descriptions To verify the performance of SUT to forward IPv4/IPv6 packets in offered packets sizes. The test requires SUT to support IPv4/IPv6 dual protocol stacks.Test Methods The tester sends IPv4 and IPv6 traffic simultaneously in full duplex configuration, via SUT to the destination port, measure the throughput and latency with various ratio of IPv4 and IPv6 traffic. Send traffic with 50% of IPv4 and 50% of IPv6 and 100% offered load first time. If packet loss occurs, decrease the offere d load in 5% resolution until the difference in offered load between successful and failed tests is less than the resolution for the test. This is the zero-loss throughput rate. At the same time, measure the latency at maximum forwarding rate. Then change the ratio of IPv4 and IPv6 traffic to test again. Increase continuously the proportion of IPv6 traffic to simulate the change of traffic characteristics in the real-world network transition.Test DescriptionsOffered load (%) initial100% with 5% increment and final 0 Offered packet types IPv6Percentage of IPv4 and IPv6 traffic 50501090 (IPv4IPv6) Offered packet size (bytes) 62 512 1518Test duration of each packet size(s) 5 The test results are as followsSustainable throughput of OC-48 POS port at packet size 64 bytes with different percentage ofIPv4 and IPv6 trafficSustainable Throughput of OC-48 POS Port at Packet Size 64 bytes with different Percentage of IPv4 and IPv6 Traffic105%100% 95% 90%85% Hitachi80% NEC75% Fujistu70% Juniper 65% 60% 55% 50%50/50 40/60 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)Sustainable throughput of OC-48 POS port at packet size 512 bytes with different percentage of IPv4 and IPv6 trafficSustainable Throughput of OC-48 POS Port at Packet Size 512bytes with different Percentage of IPv4 and IPv6 Traffic105%100% 95% 90%85% Hitachi80% NEC75% Fujistu70% Juniper65% 60% 55% 50%50/50 40/60 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)Sustainable throughput of OC-48 POS port at packet size 1518 bytes with different percentage of IPv4 and IPv6 trafficSustainable Throughput of OC-48 POS Port at Packet Size 1518 bytes with different Percentage of IPv4 and IPv6 Traffic105%100% 95% 90%85% Hitachi80% NEC75% Fujistu70% Juniper65% 60% 55% 50%50/50 40/60 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)Average latency (us) at test packets size 64 bytes with different percentage of IPv4 and IPv6 trafficAverage Latency (us) at Test Packets Size 64 bytes w ithDifferent Percentage of IPv4 and IPv6 Traffic100908070605040302010050/50 40/6 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)HitachiNECFujistu JuniperAverage latency (us) at test packets size 512 bytes with different percentage of IPv4 and IPv6 trafficAverage Latency (us) at Test Packets Size 512 bytes with Different Percentage of IPv4 and IPv6 Traffic100908070605040302010050/50 40/60 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)HitachiNECFujistu JuniperAverage latency (us) at test packets size 1518 bytes with different percentage of IPv4 and IPv6 trafficAverage Latency (us) at Test Packets Size 1518 bytes withDifferent Percentage of IPv4 and IPv6 Traffic100908070605040302010050/50 40/60 30/70 20/80 10/90IPv4/IPv6 Test Packets Percentage (IPv4/IPv6)HitachiNECFujistu JuniperIPv6 over IPv4 Configured Tunneling Performance of OC-48 POS PortTest Description Tunneling technology is an effective means to connect separate IPv6 networks via IPv4 backbone. This item is to verify the performance of SUT when SUT encapsulates IPv6 data packets into IPv4 payload and forwards the packets.Test Method The tester sends IPv6 data packets to SUT, and configures an IPv6 over IPv4 tunnel between SUT and the tester. Thus after SUT receives pure IPv6 packets from the tester, it will encapsulate it into IPv4 packet payload, and send IPv6 packets to destination over IPv4 network. The tester analyzes the packets forwared by the SUT at receiving end, calculates the throughput of SUT for different sizes of packets under the IPv6 over IPv4 configured tunnel. Test ResultsIPv6 packet size 512Destination address of sending IPv6 data packets 3FFE0042/64Bandwidth range of sending IPv6 tra

No comments:

Post a Comment

Note: Only a member of this blog may post a comment.